Created with Sketch. Created with Sketch.
Toggle menu
800-644-1756
    • Shop by Category
  • Long Range MetalHead AMS Sensors
  • Proximity Sensors
  • Capacitive Sensors
  • Photoelectric Sensors
  • Pneumatic Sensors
  • Thermo Sensors
  • Ultrasonic Sensors
  • Safety Light Curtains
  • Cables and Connectors
  • LED Indicators and Machine Lights
  • Sensor Accessories & Protection
  • Downtime Reduction
  • Sensor Testers
    • Shop by Brand
  • Panasonic
  • HTM Sensors
  • Optex
  • Murr
  • Unitronics
  • ATP
  • Amphenol
  • Belden
  • HTMåâÌÔå¢ Sensors
  • View all Brands
  • Long Range MetalHead AMS Sensors
  • Proximity Sensors
  • Capacitive Sensors
  • Photoelectric Sensors
  • Pneumatic Sensors
  • Thermo Sensors
  • Ultrasonic Sensors
  • Safety Light Curtains
  • Cables and Connectors
  • LED Indicators and Machine Lights
  • Sensor Accessories & Protection
  • Downtime Reduction
  • Sensor Testers
    • Shop by Brand
  • Panasonic
  • HTM Sensors
  • Optex
  • Murr
  • Unitronics
  • ATP
  • Amphenol
  • Belden
  • HTMåâÌÔå¢ Sensors
  • View all Brands
    • Holiday Closures

    M18 Thermo Sensor

    m18-thermo-sensor.jpg

    SA-80T-2A (for measuring temperatures up to 200°C)

    SA-80T-4A (for measuring temperatures up to 400°C)

     Model #
    		SA-80T-2A SA-80T-4A
     Temperature Range
    0 to 200°C
    		 0 to 400°C
     Area Size
    ø80/500mm
     Optics
    Silicone Lens
     Spectral Response
    Thermopile / 8 ~ 14µm
     Response Time
    100ms / 90%
     Accuracy
    0~200°C: ± 2°C, 201~400°C: ± 1%
     Repeatability
    		 ± 1°C of reading value
     Analog Output
    4-20mA
     Emissivity Ratio (ε) Adjustment
    0.95
     Power Supply
    12 - 24 VDC ± 10%, 70mA max.
     Ambient Temperature
    0 to 70°C
     Environmental Humidity
    35 to 85% RH (without dew condensation)
     Storage Temperature
    -20 to 70°C
     Vibration Resistance
    10-55Hz, amplitude 1.5mm, two hours each in direction X,Y, Z
     Water Resistance
    IP67
     Materials SUS / AI
     Weight 180g
     

    sa80t-dimen.jpg

     Maintenance
     Lens Dust or dirt adhering to the lens and flaws on the lens may cause incorrect measurement. When the lens is dirty, remove the adhering object from the lens using a blower for lens cleaning etc.
    If dirt remains wipe the lens softy using a cotton swab or lens wiping cloth moistened with a small amount of ethyl alcohol.
     Unit When the unit is dirty, wipe it off using a cloth moistened with a small amount of ethyl alcohol.
       
     Problems  Cause  Solution
    Unmeasurable The power source is not connected properly Check the lead wires and the connection.
    The power voltage needs to be adjusted to the 12-24 VDC range. Check the power voltage and adjust it to be in the 12-24 VDC range.
    The measured figure is odd The lens is dirty Refer to the lens section in the manual under "Maintenance"
    the measuring area is off center. Aim the target which should be within the field of view area for the sensor.
    Near the object to be measured another object emitting high temperatures is affecting the temperature reading. Block the heat source using a board, etc.
    The measured figure is not stable The sensor is vibrating. Prevent the vibration
    The temperature of the sensor changes suddenly. Put the sensor aside for a while to stabilize the sensor's temperature.
           Safe Usage The instruction manual contains various warnings for your safety and proper usage to avoid possible personal injury. Please be sure to heed the warnings and strictly follow safety instructions.
    Download PDF spec sheet and Instruction manual here.
     
    • SA-80T-2A
      Quick view
      SA-80T-2A

      M18 Thermo Sensor, SUS barrel, 4-20mA output with reliable detection up to 200 degrees C

      $556.25
      Add to Cart
    • SA-80T-4A
      Quick view
      SA-80T-4A

      M18 Thermo Sensor, SUS barrel, 4-20 mA output with reliable detection up to 400 degrees C

      $556.25
      Add to Cart
    Compare Selected
    customer service software